dumpspedia logo
What is the recommended protection to be used when creating a VPLEX Logging Volume?
Which type of statistics are used to track latencies, determine median, mode, percentiles, minimums and maximums?
A customer is verifying the host environment before scheduling a VPLEX NDU. According to EMC best practices, which PowerPath load-balancing policy is applied by default to all platforms?
A customer wants to add a mirror to a VPLEX Local RAID-0 device.
Which RAID type is created after the command "device attach-mirror"?
After registering Cluster-2 with ESRS during a VPLEX Metro cluster build, what is the next step to perform before the cluster is successfully built?
Refer to the exhibit.
You have created a Distributed Device in a VPLEX Metro. You want to confirm you have chosen the correct volumes before performing a mobility job across clusters. You will be moving the device to cluster 1.
Which object will be the source for this operation?
Which VPLEX component can determine the difference between a partition and a site failure of a VPLEX Metro configuration?
An EMC customer wants to add a mirror to a VPLEX Local RAID 0 device. Which RAID type is created after the device attach-mirror command is issued?
You have added a new storage array into VPLEX, but it does not see it. Which VPLEX command will display the new storage array?
Refer to the exhibit.
You are preparing to upgrade a VPLEX Metro system. You ran the version command to begin the verification process and received the output shown.
What is the most likely reason for the warning?
Exhibit:
Which VPLEX object contains virtual-to-physical mapping information and must be stored on multiple arrays?
Which command script must be executed when upgrading a small VPLEX to medium VPLEX?
Refer to the exhibit.
You are planning to perform data mobility between VPLEX Clusters using the GUI. What mobility job options do you have?
Refer to the exhibit.
You have created a Distributed Device in a VPLEX Metro. You want to confirm the volumes before performing a mobility job within the cluster. You will be moving the device to cluster 1.
Which object will be the source for this operation?
A customer has a VPLEX Metro/GEO environment and is requesting that the VPLEX Witness be installed.
The requirements for the Witness are:
What platform type is supported?
What is the EMC best practice for the optimum number of active back-end storage paths per director for each LUN presented to VPLEX?
During an installation, the physical equipment inspection reveals an ESX host used for VPLEX Witness is located in the same rack as VPLEX cluster 1 Engine. What needs to be done?
Refer to the exhibit.
You have opened the VPLEX Unisphere Manager to validate the health of the system.
What is the most likely reason for the Operational Status indicator?
In the distributed cache architecture, how much local cache does a VS2 director have?
Do virtual volumes need to be taken off-line prior to upgrading VPLEX software, and why or whynot?
Which protocols are required for a service laptop to communicate with and maintain a VPLEX environment?
A customer created a local RAID-0 virtual volume and decided that they require increased data protection by introducing a distributed virtual volume. What is the best method to convert this virtual volume without introducing any downtime to the host?
Click on the calculator in the upper left corner. How much distributed storage can be managed by a 20 GB logging volume?
What is the EMC best practice for the optimum number of back-end storage paths per director presented to a LUN?
Refer to the exhibit.
Reference the message type shown at point "1".
What type of response will be sent back to the SNMP management server from the SNMP Agent?
Refer to the exhibit.
What is the function of the two highlighted VPLEX VS2 modules?
Following EMC best practices, what information is required to register a VPLEX on an ESRS portal?
In a VPLEX Metro with Witness, which command returns the remote VPLEX management IP address and the witness public IP address?
During the installation of a VPLEX Local, the command ‘configuration system-setup’ is issued. What is accomplished by this command?
Refer to the exhibit.
You are preparing to perform an upgrade on an unconfigured VPLEX Metro. When you run the ndu pre-check command, it indicates that it has failed and there are no first upgraders. In your troubleshooting, you run the version -a command.
Based on the output, what is the reason for the failure?
medium-sized VPLEX clusters are connected via IP with a round-trip latency of approximately 35 ms.
What type of configuration is this?
Refer to the exhibit.
A customer needs to provision storage to a host on Cluster 1, but there is no additional local array capacity to allocate. How could the customer facilitate assigning storage to the Cluster 1 host from an array locally connected to Cluster 2?
Refer to the exhibit.
You have created a Distributed Device in a VPLEX Metro system. Which VPLEX Object can be placed in a Storage View for Cluster-1?
A customer has a VPLEX Metro configuration across two data centers 200 km apart. During an overnight backup, the WAN-COM link between the two data centers fails.
Which volume allows for future incremental re-synchronization with the remote mirror once the link is restored?
A service provider has implemented a VPLEX Metro cluster without the VPLEX Witness, but has implemented a static rule set. The static rule set has been set to "Cluster-2 detaches". A Windows host in the Cluster-1 data center uses a distributed volume. The inter-cluster link fails. What happens?
When configuring a RAID-1 logging volume, what flags must be used in the command line?
You are preparing a site for a large Metro VPLEX cluster. The storage administrator wants to prepare the storage network configuration and needs to ensure easy troubleshooting of storage path faults.
How many WAN-COM zones per fabric will need to be created?
A new VPLEX cluster has been configured. However, you are unable to register any host initiators. After verifying that the host has been properly zoned to the VPLEX cluster, you still cannot register them. What is a possible cause?
In a VPLEX Metro/Geo, which vplexcli command can help to troubleshoot directors latency and routing issues to other Cluster directors?
You have added a new storage array to your environment, but VPLEX, does not see it. Which VPlexcli command will display the new storage array?
You are using VPLEX Unisphere to perform management functions in your environment. You are tasked with creating several volume migrations to a new storage array.
What tab should you use to perform this migration?
You are configuring a single engine VPLEX Metro to support both local and distributed volumes. The VPLEX will utilize 10Gb WAN-COM modules in a routed configuration.
According to EMC best practices, what is the minimum number of subnets and IPs required?
Following EMC best practices, which information is required to register a VPLEX on an ESRS portal?
Refer to the exhibit.
The customer has not followed EMC best practices when cabling their VS2 VPLEX engine. You are asked how to re-cable the engine to adhere to best practices. What is your response?
Which unique logical identifier is used when determining the relationship between a virtual volume and the back-end storage array?
A customer has purchased a dual engine VPLEX Metro cluster. During installation, there are not enough free SAN ports to connect all WAN-COM ports to the SAN. What is the recommended approach?
What can you use to generate a list of VPLEX fabric initiator and target identifiers?
TESTED 21 Nov 2024
