H35-460 Sample Questions Answers

In the Sub 6G band, what is the maximum number of wave speeds for SSBs in 5G?

How many DC power outputs can the DCDU-12B provide?

In the scenario of NSA networking, gNodeB's S1-U interface is self-built, which objects are unnecessary?

Regarding the NR slot structure, what are the correct terms described below?

When the maximum power consumption of the RF cross block is < 800W, which of the following power supply scheme is the most suitable?

Considering compatibility, the BBU5900 chassis supports all BBP series single boards for LTE.

Under NSA networking, which of the following commands can be used to check whether the S1-U interface is normal?

gNodeB's baseband device BascbandEQM is an optional addition.

The transmitted DSCP value indicates the differential service code priority, the larger the value, the higher the priority.

QoS of gNB implements hierarchical congestion management of services by mapping DSCP values.

The number of empty openings required for the power modules of the BBU5900 is the same as that of the BBU3900.

What is wrong with the description of the Mandarin Duck Line test on the U2000?

What is the fiber pulling capacity between AAU and BBU using eCPRI schemes

Which of the following does not belong to the BBU board?

The maximum transmit power of NRDUCELTRP in the gNode configuration is BBU RF power.

In the NSA networking option3x scenario, which MOs in the S1 interface self-creation configuration of gNodeB are not needed and must be configured?

Which MML command is used to add MCC and MNC information to gNodeB?

In 5G base stations, which of the following is correctly interpreted regarding the ".ecf" suffix?

AAU5613 can operate in the 3.5Ghz band.

Which device makes the judgment on the change of auxiliary station under the NSA architecture?

Which of the following models of power modules can be adapted to the BBU5900?

The bandwidth of PRACH in NR is fixed.

Which of the following MML commands supports unblocking gNodeB cells?

In order to obtain a high upstream rate, the transmit power of the CPE needs to be set to the maximum power of the generator

Which of the following protocols/data falls under Tier 3?

AAU/RRU and BBU fronthaul fiber is less than 100 meters, mostly used in CRAN centralized site solutions.

In order to support the NSA DC feature on the base station, which of the following options need to be configured?

How many 100MHz NR cells does the AAU5613 support in the 17.5G RAN2.0 version?

The MCC and MNC information added by gNodeB in the SA architecture should be consistent with the core network PLMN information.

If a CPE Pro device forgets its password, how long can I press the reset button on the near end to perform a factory reset?

gNodeB uses which command to configure S1 interface information?

The VLNA group mode of gNodeB can tag different traffic with VLAN tags based on service type.

5G RAN 2.0 version gNodeB logical cells and sector devices use the command ANDD NRDUCELLTRP to complete the binding.

DCDU-12B is a DC power distribution unit, how much DC power input does it provide to the components in the cabinet?

VSWR testing on U2000 will cause business interruption and prohibit operation when business is busy.

Which of the following is not a BBU veneer?

In the 5G network test, what is the test distance between the CPE and the gNB on the terminal side?

During the 5G test, if the PC is directly connected to the LAN port of Huawei CPE through the network cable, the IP address must be manually configured on the PC to be normal

What is the maximum number of RANKS supported by CPE Pro?

Which of the following signals reflects the coverage of the NR network uplink?

In the Sub 3G band, the maximum beam number of SSBs in the NR is 16.

Before the gNode configuration is adjusted, in order to avoid alarm reporting and display in the network management foreground, the project status cannot be set to which of the following states?

The rate mode of the gNodeB Ethernet port needs to be consistent with the docking interface.

Which of the following two cells has a large interference from PBCH?

What is the maximum number of UBBPwfl boards supported by BBU5900?

What are the configuration modules that differ between the gNodeB data configuration and the LTE data configuration MML command?

gNodeB alarm level includes emergency alarm, important alarm, secondary alarm and prompt alarm, and the alarm level cannot be changed.

When a CPE device is upgraded in the near end, the firmware upgrade of the primary and standby areas can be completed at the same time as the "Update" upgrade operation.

What is the MML command used by gNodeB to add CI port configuration?

The DCDU-12B provides DC input to various components within the cabinet. When the number of configured RFUs exceeds the number, two DCDU-12Bs need to be configured.

When debugging the NR base station through the near end of the USB flash drive, which of the following conditions will cause the RU indicator of the main control board to be in the "load failed" state?

Which entity is used in the RLC layer for detection and error correction?

When gNode configures the S1 interface user plane link, you also need to obtain the port numbers of the local end and the peer end.

Which MML command is used to add trace area information to gNodeB?

Which channel is 5G used for downlink data demodulation and time-frequency synchronization?

Which of the following X2 interconnect schemes are supported by LTE and NR base stations?

In the Decore selection network of the NSA core network, the service MME assigns DCN? to UE based on which information in the UE subscription information

Regarding DWP, what are the correct descriptions of the following? (Multiple Choice)

After the new NSA network is turned on, which of the following phenomena can be observed?

To delete the original default data before configuring gNodeB, you need to complete the initialization of the base station configuration.

gNodeB ships with a default SCTP parameter template.

What is the application type used for gNodeB remote maintenance channel detection?