EMC D-VPX-OE-A-24 Dumps

When provisioning LUNs from an ALUA-capable back-end array to VPLEX, it is required that each VPLEX director has at least two paths to both the active and non-preferred array controllers. This ensures redundancy and continuous availability of data even if one path or controller fails.

ALUA-Capable Arrays: ALUA (Asymmetric Logical Unit Access) arrays present active and non-preferred (or passive) paths to the storage.The active paths are used for I/O under normal operations, while non-preferred paths are available for use if the active paths fail1.

Path Requirements: For each VPLEX director, there should be at least two paths to the active controller and at least two paths to the non-preferred controller.This configuration provides redundancy and supports the ALUA functionality1.

VPLEX Director Connectivity: VPLEX directors manage the paths to the storage arrays.Having multiple paths from each director ensures that VPLEX can continue to provide access to the LUNs even if there are issues with one of the paths or controllers1.

Redundancy and Availability: The path requirement is crucial for maintaining high availability and redundancy, which are key benefits of using VPLEX in conjunction with ALUA-capable arrays1.

Best Practices: Following this best practice for path connectivity aligns with VPLEX’s goal of providing continuous data availability and seamless failover capabilities in the event of hardware failures or maintenance activities1.

By adhering to the path requirement of having at least two paths to both the active and non-preferred array controllers, VPLEX can leverage the ALUA functionality of the back-end array to ensure optimal performance and data availability.

When setting up a VPLEX system that uses ESRS (EMC Secure Remote Services), it is essential to ensure that the correct ports are open to allow for various types of communication, including access to the VPLEX GUI. The port that needs to be opened on the firewall to allow access to the VPLEX GUI is port 443.

Port 443: This port is commonly used for HTTPS traffic, which is the protocol used for secure web communications.The VPLEX GUI is accessed over a web browser using HTTPS, hence the need for port 443 to be open1.

Firewall Configuration: The firewall administrator must configure the firewall to allow inbound and outbound traffic on port 443 to the VPLEX system’s IP address.This ensures that the technical support engineer and other users can access the VPLEX GUI through a secure connection1.

Troubleshooting Access Issues: If the technical support engineer cannot access the VPLEX GUI, one of the first steps in troubleshooting is to check the firewall settings to confirm that the necessary ports, including port 443, are open1.

ESRS Communication: While ports 25, 9010, and 5901 are important for ESRS communication and other services, they do not facilitate access to the VPLEX GUI.Port 25 is typically used for SMTP email services, port 9010 may be used for internal services, and port 5901 could be used for VNC or other remote access protocols1.

Secure Access: Opening port 443 not only allows access to the VPLEX GUI but also ensures that the communication is encrypted and secure, protecting sensitive data and system configurations1.

By opening port 443 on the firewall, the company ensures secure and reliable access to the VPLEX GUI for administration, monitoring, and troubleshooting purposes.

The data mobility operation that removes the pointer to the source leg of a RAID-1 device in Dell VPLEX is the “Clean” operation. This operation is part of the data mobility process in VPLEX, which involves migrating data from one storage volume to another.

Data Mobility: Data mobility in VPLEX allows for the non-disruptive movement of data between storage volumes, which is often used for technology refreshes, load balancing, or other maintenance activities1.

RAID-1 Device: A RAID-1 device in VPLEX is a virtual volume that provides data redundancy by mirroring data across two storage volumes, known as legs1.

Clean Operation: The “Clean” operation is used after the data has been successfully migrated to the new storage volume (target leg).It removes the pointer from the old storage volume (source leg), effectively completing the migration process1.

Pointer Removal: Removing the pointer to the source leg is an important step to ensure that the VPLEX system no longer references the old storage volume for read or write operations, and all I/O is directed to the new volume1.

Finalization: Once the “Clean” operation is performed, the source leg can be safely decommissioned or repurposed, as it is no longer part of the RAID-1 device configuration1.

By using the “Clean” operation, administrators can ensure that the data mobility process is completed efficiently and that the VPLEX system maintains data integrity and continuity of service.